Sold on Amazon — Prime shipping, easy returns 30-day easy returns Founded 2025 · Small-batch tools
Baking

Lattice Pie Crust, Step by Step (No Weaving Required)

The one-pass lattice cutter method: cold dough, one confident roll, a gentle stretch — and a bakery-window pie top.

August 18, 20263 min readotawe™ Test Kitchen

A lattice top is pie theater. Steam vents through the gaps so the fruit thickens instead of boiling over, the crust bakes crisp instead of soggy — and it looks like you apprenticed in a bakery. The traditional method takes twenty minutes of weaving cold, fragile strips. The lattice cutter method takes one pass. Here’s the full technique.

What you need

A chilled double-crust dough (your favorite recipe or a quality store-bought), flour for dusting, a rolling pin, the Otawe Lattice Pastry Cutter, one egg for wash, and coarse sugar if you’re feeling fancy.

Step 1 — Roll the top crust, then chill it again

Roll the dough to a 12-inch round, about ⅛-inch thick, on lightly floured parchment. Then slide it — parchment and all — onto a sheet pan and into the fridge for 10–15 minutes. Cold dough is the entire secret: the wheels cut cleanly through firm butter, and the lattice stretches without tearing.

Step 2 — One confident pass

Set the cutter at the edge of the dough and roll straight across in one smooth, firm motion — like a pizza wheel with commitment. The staggered wheels leave a field of short slits. Don’t saw back and forth; one direction, steady pressure, done.

Test Kitchen note

Dust the dough (not the cutter) lightly with flour before the pass. If any slit doesn’t fully open later, a paring knife tip fixes it in a second.

Step 3 — The stretch (this is the magic)

Lift the cut sheet by the parchment and flip it centered over your filled pie. Now gently pull the dough outward from opposite sides. The slits open into diamonds — and suddenly there’s the lattice. Wider stretch, wider windows; subtle stretch, tighter weave-look. You decide the style.

Step 4 — Trim, crimp, wash, bake

Trim overhang to ¾ inch, tuck it under the bottom crust’s edge, and crimp with fingers or a fork. Brush with beaten egg, scatter coarse sugar, and bake as your recipe directs — typically 20 minutes at 425°F to set the crust, then 35–45 minutes at 375°F until the filling bubbles through the lattice windows. Bubbling in the middle, not just the edges, is the honest doneness signal.

“Cold dough, one pass, gentle stretch. The lattice was inside the dough all along.”

Troubleshooting

The dough tears when I stretch it

Too warm or rolled too thin. Chill 10 more minutes and stretch with flat palms, not fingertips.

Slits closed up in the oven

They were stretched too subtly — open the diamonds a touch more next time, and chill the assembled pie 15 minutes before baking so the pattern sets.

Bottom crust is pale

Bake on the lowest rack, ideally on a preheated sheet pan or baking steel.

Beyond pie

The same cut-and-stretch move dresses up beef Wellington (wrap the lattice over the pastry before the egg wash), fruit tarts, hand pies, and even focaccia-style breadsticks. Anywhere pastry wants to look expensive, one pass gets you there.

Sources & further reading

  1. King Arthur Baking — Pie crust techniques, temperatures & troubleshooting
  2. Serious Eats — The science of flaky pie dough (butter temperature & lamination)
  3. USDA FSIS — Safe internal temperature for beef Wellington & meat pies
  4. Otawe Test Kitchen — 14 test pies, apple & sour cherry, July–August 2026
O

otawe™ Test Kitchen
Recipes and techniques tested on real grills and real weeknights by the Otawe team.

Keep reading

More from the Test Kitchen.

All articles
Baking
August 18, 20263 min read

One-Pass Lattice Apple Pie (Full Recipe)

Deep-dish two-apple filling under a bakery-window lattice — cut in one pass, stretched open, and baked until it bubbles through the windows.

Otawe™

Put it to work.

Every guide on this site was written around tools we actually make.

Shop Otawe tools